Clone-a-Willy: The Most Fun Way To Clone Your Penis

Clone A Willy is a penis casting or penis modeling kit for those who don’t know it yet. These custom dildo kits have everything you need to create amazingly detailed, vibrant penis replicas or anything your naughty brain can imagine! The DIY dildo set promises to make dildos and is incredibly accurate. The penis casting kit uses 100% body-safe materials to provide essential details. You will be amazed to see that the veins and texture of your skin are precisely replicated on a dildo.

Many people complain that their dildos always go wrong with this set. But don’t worry, I have your back. In this article, I will walk you through making your homemade dildo, and you will get a perfect copy of your willy that you can imagine. So far, I have made over 10 dildos with this kit, so I consider myself an expert in producing a willy.

The Ingredients

Before starting, let me tell you what all you get in the kit:

• A pouch of molding powder
• A cheap vibrator
• A thermometer (!)
• A balsa wood stick for stirring
• Two jars of silicone gel

Be careful not to damage or throw away the plastic container they have given, as this is the container where the penis is in, and make mold the dildo! You just have to cut it a little bit, because I’m sure you don’t have a 15cm willy, do you?

With the products neatly assembled on the table, you will need to assemble some essential tools and equipment so that the whole process can continue.

Use the following checklist to get more stuff:

• Measuring cup
• Large mixing bowl
• An accurate timer
• Scissors
• A disposable container to mix silicone in
• Four-inch square cardboard to suspend the vibrator as the dildo hardens
• A strong nylon thread

The Making of the Dildo!

It certainly isn’t so as daunting as the whole deal might sound. It could be a rather enjoyable couple activity if you look at it.

First of all, go through your instruction manual properly. Yes, read it twice, so you don’t miss any point.

Now, let’s begin!

1. Cut the molding tube to the correct length.

   Place the tube next to your hard erect penis. Mark half an inch from the head of the penis on the tub and cut it off at that end.

2. Get 415mL of water and heat it to 90°F.

   The water needs to be precisely 90° and measure a volume of 415mL. It will only mix well with the other components and ensure a perfect mold set.
   You can use the thermometer present in the Clone A Willy kit to check the temperature of the water at regular intervals.

3. Get your timer at 60 seconds and mix the water with the molding powder.

   As you find the water heating up to 90° (repeating!), cut open the bag of molding powder, then start your timer for exactly 1 minute. And then, pour the molding powder into the water and start mixing with the help of a spatula. 60 seconds is all you got.

   Mix for 60 seconds and pour it into the cylindrical container you trimmed initially. Don’t worry. The mixture would still be a bit lumpy.

4. Set your timer to 120 seconds and dive your dick into the clumpy-gooey mixture

   Be careful to place the penis in the cylinder and make sure it stays stiff for 2 minutes. You can use stimuli of various kinds to stay hard; I joined my husband and teased him about keeping the boner going.
   This is important because if your penis softens or loses hardness midway, the mold may collapse, giving you a smaller and less impressive version of a tight penis. You can even use a cock ring if that’s your thing!

5. After the timer hits 2 min, take your dick out SLOWLY and STEADILY.
   
   After removing the willy from the genital form, let it dry for 4 hours before proceeding to the next step. If you’re confused, I’m talking about mold, not your genitals.
   As for your penis, go straight to the toilet and wash it well with soap. Although every product here is biologically safe, it is better to maintain hygiene.
   The instructions usually require you to wait 2-4 hours. But take my advice and let it work all night. Let the mold sit for about 8-10 hours for the best results.

6. Mix the two jars of silicone and pour in

   Stir the silicone fluid for another 2 minutes with a stirrer. Strictly adhere to these timings for best results.
   Once you insert the vibrator into the fluid kit, it will rise. Eventually, the fluid goes into a thick form until only an inch from the top remains. Do not worry; this one-inch gap is left for the vibrator. If you don’t want a vibrator, fill it in as usual.

7. Insert your vibrator into a cardboard holder
   
   Take a square carton and cut the small X in half. Push the vibrator through the X on the cardboard box. This is done so that the vibrator does not immerse itself inside the mixture and hang on the carton.
8. Place the vibrator precisely in the center.
   
   Place the vibrator right in the middle of the liquid mold using the cardboard support. Take care so as not to tilt the whole thing, as that will displace your vibrator.
9. Leave the setup undisturbed for at least 30 hours.

   Keep the whole thing in a safe undisturbed location and get back after 30 hours. Once again, the instruction manual says only 24 hours but trust me, 30 is the minimum. I have tried and tested it.

Once the item hardens, remove it from the mold, wash it with soap and water, and you’re good to go!

If you follow every step down to the last detail, I’m sure you will have the beautiful copy of your penis you’ve always wanted. Things can go wrong on the first try, so always buy a second package ready (not to mention more dildos!).